Common Washing Machine Problems

While technology is unquestionably built with a shelf life these days and not to last as it once was, most common faults when it comes to household appliances are down to user error and not to the mechanics or make up of the machine itself. How many times have you overloaded your washing machine, used the wrong detergent or used the right detergent but put it in the wrong place? Sometimes it’s a genuine mistake but mostly it’s done under the false premise that if you wash more things together you’ll use less electricity, less water, saving you time and money but it’ll cost you a lot more to get it fixed than it would to separate your washing out into manageable loads.

The average washing machine is designed to be used no more than around five times per week and you really shouldn’t need to use it more than this. If you follow this rule, your washing machine should last between six and eight years but be prepared for this figure to be a lot lower if you consistently pack clothes, towels and bedding into the drum maytag washer repair los angeles.

The following are common problems that can often be prevented by following manufacturer’s guidelines on load size, detergent, serving and maintenance but if necessary be fixed easily and quickly by a trained appliance repair engineer.

The machine stops mid cycle – This can be very frustrating as a load of washing will be trapped and you’ll have to call in a professional but on the plus side, the problem will probably be a simple one and getting it fixed will be considerably cheaper than recycling the old and buying new.

The machine is noisier than usual – This is more than likely caused by a bearings problem and this can be diagnosed by first determining when it is at its noisiest (i.e. when spinning or when still) and by opening the door of the washing machine and moving the drum directly up and down with your hands – if this causes a noise then your bearings have probably worn out and will need replacing. This is a cheaper and longer term solution than buying a new machine.

There is water leaking from the washing machine – This is probably due to a worn seal or drain hose or potentially a problem with the solenoid valve which is the part which controls how much water is fed into the drum during a cycle. Replacements for any of these three things are inexpensive but it’s important to get the problem properly diagnosed by a professional.

How to Troubleshoot a Gas Dryer

If your gas dryer does not work at all you can check the power coming from your house, the door switch, timer, and thermal fuse. To check if there is power, first see if your dryer is plugged in. (Yes, it might sound stupid, but it happens more often than you’d think!) Does the power outlet where the dryer is plugged in work? To test that, plug a lamp or something else in the outlet and see if it works. Also, check the circuit breaker and see if something has tripped a circuit or blown a fuse. If your door switch is faulty, then that could be a reason why your gas dryer doesn’t work at all. Your door switch is located inside the dryer main housing next to the door frame. If the part tests out bad, then you should replace it. Next, you can check the timer to see if that is the problem, basically if there are open contacts in the timer it won’t work. Lastly, you can check the thermal fuse. The fuse is actually a safety precaution measure in the dryer; it will blow if your dryer overheats. This fuse is located on the exhaust duct inside the back cover panel. If your fuse has blown, and you test it with ah ohm meter, it won’t have continuity. If this is what is causing your dryer to not work at all, you will need to replace the fuse because it cannot be reset.

If your dryer is not heating, you can check the igniter kenmore dryer repair los angeles, gas valve coils, and the thermal fuse. Most gas dryers use an electronic type of igniter to ignite the gas coming in from the gas valve. If it glows a bright orange, it is working properly. When your igniter burns out, the dryer will still tumble your clothes, but there won’t be heat because the gas cannot ignite. If your igniter is burned out you will need to replace it. The igniter is located inside the dryer housing, near the front and towards the bottom. The igniter is usually in a metal cone shaped tube. It’s mounted to the far end of the burner tube and it should have some wires attached to it, or to the tension bracket. The next thing you can test are the gas valve coils. The first thing to watch for is the igniter, if it glows orange and then shuts off without igniting the gas, then there may be some faulty coils on your gas valve. When these coils get energized, they open the gas valve. If they are faulty then the valve won’t open and the gas can’t ignite. If this is the case with your dryer, it’s best to replace all of the coils at the same time. To check the thermal fuse, you can follow the exact instructions I stated in the previous paragraph.

If your dryer takes too long to dry your clothes you can check the vent, the flame sensor/gas valve, internal ductwork, and the cycling thermostat. Most of the time there is some sort of clog inside the venting that goes from your dryer to outside of the house. For a dryer to heat up, the duct has to be clear of any sort of clog or lint. To clean this out, you can use a vacuum. Also, vent cleaning should be done at least once a year, if you do laundry often. Next, you can check the flame sensor/gas valve. The flame sensor is next to the igniter. The gas may shut off before the cycle is finished if the flame sensor is defective. Sometimes one of the electrical coils on the gas valve fails. If this happens, the flame will shut off before your thermostat can send a signal, which will make the drying time a lot longer. If the sensor or the coils are the problem, replace them. If your dryer’s internal ductwork gets clogged, it won’t be able to run correctly. Most of the time you will need to disassemble your dryer to reach the ductwork, to clean out the clog. You can check this quickly by sliding out your lint filter, and use a flashlight to look inside the duct. If you see a buildup of lint, you should clean it out with a vacuum. However, if you can’t remove the clog with a vacuum, you might call a serviceman to do that for you. The cycling thermostat is not a common reason why your dryer would take a long time to dry clothes, however it does happen sometimes. If this thermostat breaks, it can cause your dryer to heat improperly. You should replace it if it is faulty.

In summary, if this guide did not help you fix your problem, you should contact an appliance technician to repair it. However, I hope this article was handy in giving you some information on how to troubleshoot your gas dryer in the future. In my next article I will help troubleshoot some more common gas dryer problems.

Main and Minor Repairs To Do Earlier than Promoting Your Dwelling

While you planning to maneuver, it’s possible that your present house might use some upgrading; in any other case, you most likely would not be shifting within the first place. In case you are getting ready to checklist your private home in the marketplace on the market, it’s clever to make some necessary repairs and renovations with the intention to get essentially the most out of your asset. Proceed studying to be taught which main and minor repairs you must contemplate and handle, in addition to, methods to get began.

Minor Repairs

Earlier than promoting your private home, there are most actually an extended checklist of minor repairs that you are able to do to make your property extra interesting to potential patrons kitchenaid dishwasher repair los angeles. Even a primary deep clear is one thing you need to significantly contemplate. Listed below are some widespread minor house repairs that property house owners will implement earlier than itemizing their properties on the market:

Paint – New paint is an on the spot refresher for any room. In case your inside has not been painted in a couple of years, a recent coat will immediately give your private home a brand new really feel and cleaner atmosphere. Simply watch out selecting paint colours. Keep away from colours which might be daring and vivid, and lean towards extra modest colours, like shades of tan, beige, taupe, grey, ivory, and even a tender olive inexperienced.

Flooring – Flooring is likely one of the prime promoting factors for potential house patrons. New or newly renovated flooring can immediately improve the look of a room, together with kitchens, bogs, dwelling rooms, bedrooms, and even garages. This consists of carpeting. In reality, many householders select to interchange carpeting with hardwood or laminate flooring since many fashionable house patrons are fascinating in fashionable designs. Moreover, carpeting begins to look outdated and worn out shortly after set up. Which means your carpet will most actually require a deep cleansing and shampoo, and even alternative, earlier than promoting your own home on the actual property market.

Lighting – One other element that basically impressed and influences potential house patrons is lighting and lighting fixtures. Outdated lighting fixtures usually are not interesting, so they may stick out like a sore thumb. Changing or upgrading your lighting atmosphere and fixtures is a superb strategy to improve your private home.

Main Repairs

Together with minor repairs, there are often a couple of main repairs you are able to do to make your private home promote sooner in the marketplace, and on the value level you need. As an illustration, home equipment are an enormous promoting level for potential patrons. Water heaters, water softeners, sump pump techniques, boilers, dishwashers, washing machines, and extra, ought to be in good situation if you wish to get essentially the most on your house.

One other key issue is roofing and siding. In case your roof and siding techniques are in dangerous form, it might most likely be profitable so that you can restore or change them earlier than itemizing your private home. In any other case, their situation will have an effect on the presents you obtain on the home. The identical precept applies to different main repairs, like basis or water injury points, mildew, pest infestations, and extra.

The place To Get Began

Contact an area and trusted house reworking contractor for assist managing all of your main and minor restore wants. They’ve the licensing, , expertise, and sources to effectively examine and restore all of the areas of your private home that concern you.

How to Select the Best Kitchen Appliances for Your Home

Choosing the right kitchen appliances for your home can be a hectic task, especially when you have so many different brands to choose from. It’s a major undertaking that requires pre-planning before you enter the nearest home improvement store.

Kitchen appliances need huge investment, so it is important to shop with caution. Amongst all, stainless steel appliances are the ones that catch our hearts. But, they are expensive compared to ordinary kitchen utensils. However, these appliances can last for decades and provide great value for the price. While relying on cheap products can be back breaking, they need frequent servicing, and the repair charge can even surpass the cost of expensive steel appliances maytag stove and oven repair pasadena.

Before taking any hasty decisions, make sure that you consider your budget, size of your kitchen, and the right appliances to suit your kitchen needs. We have mentioned afew factors that every consumer needs to consider before walking into a kitchen appliance store.

Budget and Layout

The primary factor that influences any buying decision is the budget and layout. Whether you are planning to refurbish your existing kitchen on design a new one, you’ll need appliances to remodel your cookery. The allocated budget greatly impacts your decision. So before making a purchase, prioritize cost and functions over aesthetics. An expensive cooking appliance may flaunt an appealing design, but you might end up revamping your entire kitchen, which is both costly and time-consuming.

Lifestyle and Functions

Before spending your savings on kitchen appliances, configure different specification to ensure that they are the right fit for your family’s lifestyle. The products you buy should circle the way you live and entertain. Consider how you are using your appliances currently, and how would you like to use it in the future. Don’t grab anything just because they look fancy or trendy! Instead, look for the functions that are essential for you.

And, if you want your kitchen to stand out add different and useful appliances such as ice maker, warming drawer, or even a large capacity oven. Besides that, consumers can also explore the internet and find the right products to serve the purpose.


After narrowing choices of products based on functions and budgets, consider the finishes to compliment the look of your kitchen. Stainless steel is the prominent choice for today’s modern individuals; they look classy and stylish, are durable and easy to clean. You can also make custom kitchen appliances with custom cabinetries to suit your requirement. They might come with a slightly expensive price tag, but they can completely alter the perspective of people towards your kitchen.

A major benefit of selecting high-end products is that they are created with a distinct vision to coordinate with different kitchen styles. They will serve as a reliable kitchen companions, and flaunt an illumination that will catch everyone’s heart.

Purchase Smart

When you are willing to purchase anything, it is more than essential to select the retailer wisely. Make sure that the salesperson you speak to knows about multiple brands and product specifications. He/she should be able to steer you to different products that are relevant to your search. Besides that, they must be capable to suggest you products based on the size of your kitchen.

Microwave Oven Maintenance Tips

The Microwave Oven is a vital component of nearly every home today. It is often under the authority of the lady of the house but used by every family member both young and old. While both you and I have knowledge of many excellent food recipes, it is so important to learn how to take care of this kitchen appliance properly. Electrical maintenance is most certainly the job of a licensed specialist. A homeowner’s review of a few quick and frequent inspection practices will ensure microwave oven maintenance is up kept and secure your investment over a long period of time samsung stove and oven repair pasadena.

Five things you should never do with a microwave:

1. Never operate the microwave oven empty.

2. Never use a microwave for deep-frying or canning.

3. Never use a microwave oven to heat a baby bottle.

4. Stay alert. Especially while making popcorn due to the huge amount of heat generated which often results in sudden fires.

5. Use a microwave safe bowl or container for cooking and heating.

As a general rule, never use any container that contains metal.

Cleaning the microwave after every use is very important for health and safety. Modern microwaves are equipped with a detachable, rotating glass plate at the base. After each use, the plate should be taken out and cleaned properly. This is important as the residual food particles may get heated and catch fire if not cleaned. When owners do not clean the microwave properly, leftover food particles cause the microwave to work harder and may cause microwave leakage. If your oven is not fitted with a detachable base, wipe out the base with a gentle water and soap mix and dry it perfectly before using. Good microwave cleaners can also be used.

It is important to clean the edges of the door carefully. The edges of the door are a very common area in which food particles get trapped and cause major damage to the microwave door.

It is of vital importance to take special care of the microwave oven door. The door is a very integral part of the microwave as it automatically triggers the engine and also protects users from health hazards. Sometimes if the door is damaged, but still closes, the microwave oven might not stop functioning. But you should proactively stop using it and contact a repair professional or the manufacturer for a repair.

Important! Contact the vendor’s customer support if the door is not closing tightly enough and stop using it immediately.

Most manufacturers recommend owners using an approved surge protector to protect the unit from power surges. It is recommended to plug the microwave directly into a surge protector.

Top Load Washer – Cycles of Operation

A typical wash cycle of a typical agitator-type washing machine begins with a fill period of anywhere from 2 to 5 min. depending on the water level selected and the water pressure. Maytag, Whirlpool, Kenmore (Sears), Frigidaire, and GE may have minor capacity differences and thus time differences. The washing period, which will be for anywhere from 2 to 12 minutes, also depends on the setting the operator has selected. After the wash cycle is completed, the machine pauses for 1 min for the purpose of reversing motor rotation. After the 1-min pause, water is pumped from the spin basket and the outer tub. The spin basket does not spin during this operation, although, if there is no clothing or very little clothing in the spin basket, there is a tendency for it to move slightly. The washer agitator may also move very slightly, and this must not be mistaken for a fault in the washer. The motion of both the basket and the agitator will not occur in cases where there is a least a minimum amount of clothing in the basket.

The following is the general cycle of operation washer repair altadena, with the approximate time used in the various states:

Wash fill – 3 to 4 minutes
Wash – 1 to 15 minutes
Spin – 2 to 3 minutes
Rinse Fill 3 to 4 minutes
Rinses 2 to 3 minutes
Spin Dry 3 to 5 minutes
Total Time 14 to 34 minutes

This is not exact cycle and like I said above, there are minor differences between such brands as Whirlpool, Kenmore (Sears), Maytag, GE, and others. The time for one complete cycle may range from as little as 14 minutes to as long as 34 min, depending on the particular machine and length of the washer period which the user selects.

During the washer pump out period, water enters the spin basket and removes all suds from the outer tub as well as the spin basket and clothes load. By the end of the pump out period, all water has been removed from the spin basket and the outer tub. After the pump out period, the spin basket spins under power for a period of ¼ minute. After this time, power to the motor is turned off, and the basket is free to coast. The spin basket coasts through the next 2 min. during which time rinse water enters the washer basket and pump still operates.

The initial power spin and the subsequent coasting of the spin basket, together with the spin-spray water entering the clothes, have a tendency to wash any lighter-than-water soil from the fabric and flush it away from the clothing. The washer spin basket is operating only at slow speed at this time; therefore, the clothing is not packed so tightly that a scum or lighter-than-water soil will be trapped.

After the initial spin rinse, the normal extraction spin of our typical washer occurs for a period of 2 minutes, after which the spin basket wills with water for a period of not less than 2 minutes and not more than 4 min, depending upon the original setting of the water level switch. The difference between the initial fill and the rinse fill comes about through the fact that the clothes in the spin basket contain some water which is not found in the original load.

After our typical washer is filled with rinse water, there is a 4 min period of agitated deep-wave rinse. The 1 min pause and 2 min pump out periods are repeated, after which the spin basket operates for a total of 7 min to extract water from the clothes. After the first 3/4 min, a1 /4 min spin spray occurs for an additional fresh-water rinsing. Please understand the cycle of operations, because if washers pause for 1 min and you do not realize the reason for it, you may have already have called the service technician before the machine starts again. The cycle times of various operations of the washers are given in the service manuals.

Please use this as a basic guide to understand the basic operating principles of the top-load automatic washing machine. Once again, there are slight variations between Maytag, Whirlpool, and Kenmore (Sears), so special considerations may be necessary.

How to Increase Life of Your Appliances

Most of us expect an average life from our home appliances, perhaps because we don’t know that they can last for much longer with proper cleaning. On the other hand, less cleaning may reversely decrease their life by forcing them to work harder. Since replacing an appliance or spending money on repairing may turn out to be costly, it’s always better to take some small steps of cleaning for increasing their life. In this article I want to talk about the proper ways of cleaning our home appliances:

Cleaning air quality appliances appliance repair pasadena: Air cleaners, humidifiers and purifiers usually operate for long time. Since goal of such appliances is to improve the quality and flow of air in our environment, it’s our responsibility to keep them clean. To keep them running smoothly we should change their filters and clean them for seasonal storage.
Cleaning coffee machines: I’m sure that you won’t say “NO” to a cup of coffee in the morning. But for preparing coffee it’s essential to keep your coffee machine in good condition. Coffee machines usually have shorter life in comparison to other appliances because we keep them “switched on” for most of the time. We also use them more frequently. To clean a coffee machine you should process it through a solution of white vinegar and water. Once you’ve done that, a few rinses of clean water will be enough for removing the mineral that hampers efficient operation of a coffee machine. Also if your coffee machine has automatic shut-off feature then make use of it and set it to a shorter period. Keeping coffee machine switched on even if you’re not in the mood of drinking coffee is certainly not a good idea.
Cleaning dishwashers: Some dishwashers come with in-built garbage disposal units for splitting the food particles into tiny pieces. If your dishwasher lacks such unit then it’ll be better to remove food scraps from your dishes before loading them into dishwasher. You should also take care of its door seal periodically. If dirt starts building up on seal then clean and get rid of it before it takes the figure of mold. Also ensure that seal isn’t broken or loose because it may lead to undesired leakage. In case of leakage change the seal as soon as possible.
Cleaning dryers: Let’s face it – most of us are habitual of overloading our dryers. I would like to tell you that this way we do nothing instead of decreasing their life. First of all, overloading the dryer doesn’t mean that you’ll be able to save time. Of course, you won’t have to load it multiple times. But you don’t realize that an overstuffed dryer takes longer time in drying. Second, when we overload our dryer it doesn’t get enough space for air flow, which may ultimately tax the motor. So I’ve only one advice for maintenance of your dryer – please don’t overload it.

Appliance Repair Cannot Be Ignored

When you purchase appliances, you are pretty much stuck with them for a long, long time! Most major appliances are so big that they require work just to get them into your home and set up. You have to attach them to the walls and pipes. It is a big production to say the least. That is why when they start to get old and they are not working as well as they used to, their owners go through a denial phase. Eventually, you are going to have to cave in and realize these appliance need a little assistance before they are going to start functioning properly again. When they do not work properly, you are not getting the most out of their uses. This hinders cooking, cleaning, and other general household caretaking. If you do not know how to maintain and fix these appliances yourself, then you must hire someone to do the job for you. A professional will do it quickly, so that you can get back to whatever work needs to be completed kitchenaid dishwasher repair los angeles .

When that day comes, you should start looking for a good price on repairs. You should probably first attempt to figure out what is wrong with the appliance. If it is a refrigerator, is it the temperature control? Does your gas range leak or fail to ignite? Look up a local service that can fix your brand appliances. You can do this by looking it up online by using search terms with your product in the title, such as “Viking dishwasher repair” or “Bosch dishwasher repair.” It is a good idea to be specific because it will get you better results. If you want to be more specific, you can list your location too so that you have the nearest places listed.

When selecting a place to fix whatever is broken, you should look at its credentials. You can find testimonials online. Obviously, be skeptical of the more biased reviews. Try and select a place that can get the work done for you quickly and efficiently, as well as one that has factory trained employees. Schedule an appointment if you can so you won’t be stuck at home all day waiting for a repair servicer to show up and fix your appliance.

Don’t let your kitchen become a playground for misbehaving appliances. Take care of the problem immediately after you notice it is affecting your workspace.

Repairing Amana Refrigerators

Amana refrigerators have reached a milestone in terms of their designs. The Amana name has been producing home appliances since 1934 when goods were produced under the George Foerstner name and then later in 1947 the goods were produced under the Goodman name. The company was then sold to Maytag Corporation and then the company was then bought over by Whirlpool. The Amana name now showcases some of the best home appliances that are around. This name has remained a strong trademark in terms of efficiency, design and usage. It is true to say that refrigerators are about a lot more than just the shelves and the simple buttons that are on them. These appliances are designed to keep food cool and fresh whirlpool refrigerator repair los angeles.

Amana refrigerators like all other refrigerators are also about the parts, which support these functions. Almost everyone at some point has suffered a problem with their refrigerator, and in a lot of cases this is because one of the parts has stopped working without any prior warning. In most cases these parts are not actually that easy to repair. If you telephone a refrigerator company, they usually take awhile to respond and to understand the problem. It can be a very tedious process to discover exactly what is wrong with the refrigerator in the first place. Once they have gone through this tedious process they will then send someone out to check the refrigerator and the customer will be charged for this visit.

Parts for Amana refrigerators are very useful as they are compatible with all other types and models of refrigerator. These parts are compatible with a vast array of other appliances as they are a simple design and they are made using a standardized manufacturing process. The models of Amana refrigerators are actually amongst the best in the world. It is very easy to source the different parts yourself. Then all you need to do is to get a repairman to come in to repair it.

Some people will also be able to fix the machines themselves. There are a number of different sites on the Internet that have instruction and manuals available. These manuals are very handy as you can go through them and get instructions on how to figure out the problem. This may help you to not only figure out the refrigerator problem quickly but also save you money. It is very important to be cautious though, and you should take a note of the model number and then look for the Amana refrigerator part to suit your model number.

If your refrigerator has run out of warranty then it can be expensive to get the problem fixed. Parts for Amana refrigerators can help you keep the cost down a bit therefore these parts are certainly worth taking time to look into. It may work out to be a lot cheaper to find the part yourself and then just get a mechanic to repair it for you.

Why You Want A Native Electrician for Your House Home equipment

Whether or not you are seeking to repair a routine household dinner or are making ready for the Thanksgiving feast, the failure of a kitchen dwelling equipment, like an oven can derail the plans in your meals. That is one thing that nobody needs.

You would possibly attempt to make a restore your self or idiot round with the settings in your gadgets. Who is aware of? Perhaps you will get your oven to warmth up and work correctly in case you set it to bake at 350° earlier than heating all of it the way in which to 450°. I am certain you’ve got heard your folks or household declare to have the ability to “repair” their dwelling home equipment in such a means. Nevertheless, the easy reality of the matter might be that wiring in your retailers might not be capable to deal with such electrical costs lg appliance repair pasadena.

Sadly, whenever you’re working into an issue with your private home home equipment, such fast fixes should not going to unravel the issue in the long run. As a way to correctly deal with repairs, you should name your native electrician.

What Makes Your Native Electrician Important?

It could be a disappointing factor to simply accept, however most of us should not knowledgeable repairmen. Every now and then, sure, we might be useful or discover a answer to sure issues by watching on-line movies or studying “the way to” articles. Nevertheless, the easy reality stays that most individuals ought to solely resolve issues of their skilled fields. That is simply the way in which it’s. When you select to imagine in any other case, you could possibly be inserting your self, and your family members, into hazard.

As their identify suggests, electricians resolve electrical issues for a dwelling. Electricians work with most of these issues on a day-to-day foundation. Whether or not it is the case that one among your retailers is failing to supply energy, your oven continues to close off, otherwise you maintain shedding gentle in your home, this skilled is the particular person you should name to unravel the problems you are encountering.

These professionals are skilled to assist restore energy all through your home in a secure method at instances when the electrical energy has shut off. When you can’t flip in your electrical range to cook dinner your dinner dishes, please don’t try and make sophisticated repairs your self. Sure, it is best to look into the problem to find out the entire signs of the issue. However, making an attempt to repair the problem is a harmful alternative for a non-expert.

Electricians are skilled to keep away from electrical shocks, which may show deadly in case you’re making an attempt to restore them in an unsafe method. Earlier than making an attempt to make repairs in your electrical wiring, ask your self this straightforward query: is it higher to pay a small price to an electrician or pay the worth of your very life in a failed try and get your oven to show again on in dinner time? It must be a simple option to make.

Keep in mind to decide on your native electrician in your dwelling equipment restore wants. When you’re working into points with any of the machines in your home, they’re the most effective outfitted to repair the problems for you. Be ready for his or her arrival with a full report of the identified points inside your private home.